Tooth Gem Glue: What Actually Works (and What Doesn't)

Tooth Gem Glue: What Actually Works (and What Doesn't)

For a tooth gem you don't use nail glue or super glue, but an adhesive made for teeth: an etch and bond system that you cure with UV light. That way your gem stays firmly on, and it can still be removed later.

Looking for the best tooth gem glue to apply a gem at home? Below you can read which glue works, which one to skip and exactly how Etch & Bond works.

Etch & Bond 5,000+ happy customers No nail glue or super glue on your tooth Etch & Bond is made for tooth gems and comes in every SelfGem kit. View Etch & Bond →

Why nail glue and super glue are a bad idea

Your tooth is smooth, hard and always a little wet. Regular glue isn't made for that. Nail glue, lash glue, super glue or craft glue can come loose quickly from saliva and heat, feel rough or be hard to remove. They're also not meant for use in your mouth. A tooth gem should look good and feel comfortable, so choose glue that's made for tooth gems.

What glue do you use for tooth gems?

A tooth gem holds best with a two-step system plus UV light:

  • Etch prepares the surface of your tooth so the glue can bond well.
  • Bond is the adhesive that holds your gem.
  • A UV light cures the Bond so your gem stays firmly in place.

At SelfGem that's Etch & Bond (tooth gem glue). It's made for tooth gems, comes in every kit and is also sold separately if you want to reapply your gems.

Etch and Bond: how to apply a tooth gem step by step

  1. Apply the Etch. Rub the Etch on the spot where your gem goes for about 30 seconds. Then wipe it off with a slightly damp cotton roll and dry your tooth completely again.
  2. Apply the Bond. With a new stick, apply a thin layer of Bond, not much bigger than your gem.
  3. Place the gem. Pick up your gem with the wax pencil and press it gently into the Bond.
  4. Cure. Hold the UV light as close to the gem as you can without touching it. Cure for 60 to 120 seconds, ideally 30 seconds per side.

You'll find all steps with photos in the instructions.

Why one gem lasts longer than another

If a gem falls off quickly, it's usually not the glue itself but how it was applied:

  • Moisture. Even a little saliva while applying weakens the bond.
  • Too much glue. Your gem can slide or end up stuck too firmly. With too much glue, the crystal can come off and leave a grey layer on your tooth: that's the foil of the gem, not glue.
  • Cured too briefly or too far away. Then the Bond only half cures.
  • The spot. Close to the biting edge there's more pressure, so a gem comes off sooner there.

Also read how long tooth gems last and the most common mistakes.

Temporary glue for one night?

There are also stick-on gems and temporary glue for a party or a photo shoot. They often come off as soon as you eat, drink or brush. If you want your gem to really stay on for a while, go for Etch & Bond with UV light.

Tooth gem glue FAQ

How long should etch stay on a tooth?

About 30 seconds. Then you wipe it off and dry your tooth completely.

Can I glue my gem back on if it comes off?

Yes. With Etch & Bond or the Refill Pack you can reapply your gem at home yourself. The Refill Pack also has new sticks and cotton rolls.

Why aren't the Etch & Bond bottles full?

That's how it should be. Each bottle contains about 1 ml: we sell by content, not by bottle size. The space at the top also helps prevent leaks.

Everything in one kit

Want to try it yourself? In the Mix & Match Kit you choose your own gems and get Etch & Bond, a UV light, sticks, cotton rolls and clear instructions with it. Painless, no drilling, and no salon bill. More than 5,000 happy customers have tried it.

Reading next

What Is the Best Tooth Gem Kit? How to Choose the Right One
Tooth Gem Aftercare: Brushing, Eating and What's Normal